This article may require cleanup to meet Wikipedia's quality standards. The specific problem is: Somewhat clumsy text in places, article needs a language check. (December 2017) (Learn how and when to remove this template message)
An electric-vehicle battery (EVB) or traction battery is a battery used to power the propulsion of battery electric vehicles (BEVs). Vehicle batteries are usually a secondary (rechargeable) battery. Traction batteries are used in forklifts, electric golf carts, riding floor scrubbers, electric motorcycles, electric cars, trucks, vans, and other electric vehicles.
Electric-vehicle batteries differ from starting, lighting, and ignition (SLI) batteries because they are designed to give power over sustained periods of time. Deep-cycle batteries are used instead of SLI batteries for these applications. Traction batteries must be designed with a high ampere-hour capacity. Batteries for electric vehicles are characterized by their relatively high power-to-weight ratio, energy-to-weight ratio and energy density; smaller, lighter batteries reduce the weight of the vehicle and improve its performance. Compared to liquid fuels, most current battery technologies have much lower specific energy, and this often impacts the maximal all-electric range of the vehicles. However, metal-air batteries have high specific energy because the cathode is provided by the surrounding oxygen in the air. Rechargeable batteries used in electric vehicles include lead-acid ("flooded", deep-cycle, and VRLA), NiCd, nickel-metal hydride, lithium-ion, Li-ion polymer, and, less commonly, zinc-air and molten-salt batteries. The amount of electricity (i.e. electric charge) stored in batteries is measured in ampere hours or in coulombs, with the total energy often measured in watt hours.
The battery makes up a substantial cost of BEVs, which unlike for fossil-fueled cars, profoundly manifests itself as a price of range. As of 2018, the few electric cars with over 500 km of range such as the Tesla Model S are firmly in the luxury segment. Since the late 1990s, advances in battery technology have been driven by demands for portable electronics, like laptop computers and mobile phones. The BEV marketplace has reaped the benefits of these advances both in performance, energy density. The batteries can be discharged and recharged each day.. Perhaps most notable, battery costs have plummeted, and the cost of electric-vehicle batteries has been reduced by more than 35% from 2008 to 2014.
The predicted market for automobile traction batteries is over $37 billion in 2020.
In terms of operating costs, the price of electricity to run an EV is a small fraction of the cost of fuel for equivalent internal combustion engines, reflecting higher energy efficiency. The cost of replacing the batteries dominates the operating costs.
Flooded lead-acid batteries are the cheapest and in past most common traction batteries available. There are two main types of lead-acid batteries: automobile engine starter batteries, and deep cycle batteries. Automobile alternators are designed to provide starter batteries high charge rates for fast charges, while deep cycle batteries used for electric vehicles like forklifts or golf carts, and as the auxiliary house batteries in RV's, require different multi-stage charging. No lead acid battery should be discharged below 50% of its capacity, as it shortens the battery's life. Flooded batteries require inspection of electrolyte level and occasional replacement of water which gases away during the normal charging cycle.
Traditionally, most electric vehicles have used lead-acid batteries due to their mature technology, high availability, and low cost (exception: some early EVs, such as the Detroit Electric, used a nickel-iron battery.) Like all batteries, these have an environmental impact through their construction, use, disposal or recycling. On the upside, vehicle battery recycling rates top 95% in the United States. Deep-cycle lead batteries are expensive and have a shorter life than the vehicle itself, typically needing replacement every 3 years.
Lead-acid batteries in EV applications end up being a significant (25-50%) portion of the final vehicle mass. Like all batteries, they have significantly lower energy density than petroleum fuels--in this case, 30-40 Wh/kg.While the difference isn't as extreme as it first appears due to the lighter drive-train in an EV, even the best batteries tend to lead to higher masses when applied to vehicles with a normal range. The efficiency (70-75%) and storage capacity of the current generation of common deep cycle lead acid batteries decreases with lower temperatures, and diverting power to run a heating coil reduces efficiency and range by up to 40%. Recent advances in battery efficiency, capacity, materials, safety, toxicity and durability are likely to allow these superior characteristics to be applied in car-sized EVs.
Charging and operation of batteries typically results in the emission of hydrogen, oxygen and sulfur, which are naturally occurring and normally harmless if properly vented. Early Citicar owners discovered that, if not vented properly, unpleasant sulfur smells would leak into the cabin immediately after charging.
Nickel-metal hydride batteries are now considered a relatively mature technology. While less efficient (60-70%) in charging and discharging than even lead-acid, they have an energy density of 30-80 Wh/kg, far higher than lead-acid. When used properly, nickel-metal hydride batteries can have exceptionally long lives, as has been demonstrated in their use in hybrid cars and surviving NiMH RAV4 EVs that still operate well after 100,000 miles (160,000 km) and over a decade of service. Downsides include the poor efficiency, high self-discharge, very finicky charge cycles, and poor performance in cold weather.
GM Ovonic produced the NiMH battery used in the second generation EV-1, and Cobasys makes a nearly identical battery (ten 1.2 V 85 Ah NiMH cells in series in contrast with eleven cells for Ovonic battery). This worked very well in the EV-1. Patent encumbrance has limited the use of these batteries in recent years.
The sodium or "zebra" battery uses a molten chloroaluminate sodium (NaAlCl4) as the electrolyte. This chemistry is also occasionally referred to as "hot salt". A relatively mature technology, the Zebra battery has an energy density of 120Wh/kg and reasonable series resistance. Since the battery must be heated for use, cold weather doesn't strongly affect its operation except for in increasing heating costs. They have been used in several EVs. Zebras can last for a few thousand charge cycles and are nontoxic. The downsides to the Zebra battery include poor power density (<300 W/kg) and the requirement of having to heat the electrolyte to about 270 °C (520 °F), which wastes some energy and presents difficulties in long-term storage of charge.
Lithium-ion (and similar lithium polymer) batteries, widely known via their use in laptops and consumer electronics, dominate the most recent group of EVs in development. The traditional lithium-ion chemistry involves a lithium cobalt oxide cathode and a graphite anode. This yields cells with an impressive 200+ Wh/kg energy density and good power density, and 80 to 90% charge/discharge efficiency. The downsides of traditional lithium-ion batteries include short cycle lives (hundreds to a few thousand charge cycles) and significant degradation with age. The cathode is also somewhat toxic. Also, traditional lithium-ion batteries can pose a fire safety risk if punctured or charged improperly. These laptop cells don't accept or supply charge when cold, and so heaters can be necessary in some climates to warm them. The maturity of this technology is moderate. The Tesla Roadster (2008) uses "blades" of traditional lithium-ion "laptop battery" cells that can be replaced individually as needed.
Most other EVs are utilizing new variations on lithium-ion chemistry that sacrifice energy and power density to provide fire resistance, environmental friendliness, very rapid charges (as low as a few minutes), and very long lifespans. These variants (phosphates, titanates, spinels, etc.) have been shown to have a much longer lifetime, with A123 expecting their lithium iron phosphate batteries to last for at least 10+ years and 7000+ charge cycles, and LG Chem expecting their lithium-manganese spinel batteries to last up to 40 years.
Much work is being done on lithium ion batteries in the lab. Lithium vanadium oxide has already made its way into the Subaru prototype G4e, doubling energy density. Silicon nanowires, silicon nanoparticles, and tin nanoparticles promise several times the energy density in the anode, while composite and superlattice cathodes also promise significant density improvements.
In 2010, scientists at the Technical University of Denmark paid $10,000 for a certified EV battery with 25 kWh capacity (i.e. $400 per kilowatt hour), with no rebates or surcharges. Two out of 15 battery producers could supply the necessary technical documents about quality and fire safety. In 2010 it was estimated that at most 10 years would pass before the battery price would come down to 1/3.
According to a 2010 study, by the National Research Council, the cost of a lithium-ion battery pack was about US$1,700/kWh of usable energy, and considering that a PHEV-10 requires about 2.0 kWh and a PHEV-40 about 8 kWh, the manufacturer cost of the battery pack for a PHEV-10 is around US$3,000 and it goes up to US$14,000 for a PHEV-40. The MIT Technology Review estimated the cost of automotive battery packs to be between US$225 to US$500 per kilowatt-hour by 2020. A 2013 study by the American Council for an Energy-Efficient Economy reported that battery costs came down from US$1,300 per kWh in 2007 to US$500 per kWh in 2012. The U.S. Department of Energy has set cost targets for its sponsored battery research of US$300 per kWh in 2015 and US$125 per kWh by 2022. Cost reductions through advances in battery technology and higher production volumes will allow plug-in electric vehicles to be more competitive with conventional internal combustion engine vehicles. In 2016, the world had a Li-Ion production capacity of 41.57 GWh.
The actual costs for cells are subject to much debate and speculation as most EV manufacturers refuse to discuss this topic in detail. However, in October 2015, car maker GM revealed at their annual Global Business Conference that they expected a price of US$145 per-kilowatt-hour for Li-ion cells entering 2016, substantially lower than other analyst's cost estimates. GM also expects a cost of US$100 per kwh by the end of 2021.
According to a study published in February 2016 by Bloomberg New Energy Finance (BNEF), battery prices fell 65% since 2010, and 35% just in 2015, reaching US$350 per kWh. The study concludes that battery costs are on a trajectory to make electric vehicles without government subsidies as affordable as internal combustion engine cars in most countries by 2022. BNEF projects that by 2040, long-range electric cars will cost less than US$22,000 expressed in 2016 dollars. BNEF expects electric car battery costs to be well below US$120 per kWh by 2030, and to fall further thereafter as new chemistries become available.
|Battery Type||Year||Cost ($/kWh)|
|Nickel Metal Hydride||2004||750|
|Nickel Metal Hydride||2013||500-550|
|Nickel Metal Hydride||350|
|Battery Type||Year of Estimate||Cycles||Miles||Years|
|Nickel Metal Hydride||2001||100,000||4|
|Nickel Metal Hydride||1999||>90,000|
|Nickel Metal Hydride||200,000|
|Nickel Metal Hydride||1999||1000||93,205.7|
|Nickel Metal Hydride||1995||<2,000|
|Nickel Metal Hydride||2002||2000|
|Nickel Metal Hydride||1997||>1,000|
|Nickel Metal Hydride||1997||>1,000|
In 2010, battery professor Poul Norby stated that he believed that lithium batteries will need to double their energy density and bring down the price from $500 (2010) to $100 per kWh capacity in order to make an impact on petrol cars.Citigroup indicates $230/kWh.
Toyota Prius 2012 plug-in's official page declare 21 kilometres (13 mi) of autonomy and a battery capacity of 5.2 kWh with a ratio of 4 kilometres (2.5 mi)/kWh, while the Addax (2015 model) utility vehicle already reaches 110 kilometres (68.5 mi) or a ratio of 7.5 kilometers (4.6 mi)/kWh.
Battery electric cars achieve about 5 miles (8.0 km)/kWh. The Chevrolet Volt is expected to achieve 50 MPGe when running on the auxiliary power unit (a small onboard generator) – at 33% thermodynamic efficiency that would mean 12 kWh for 50 miles (80 km), or about 240 watt-hours per mile. For prices of 1 kWh of charge with various different battery technologies, see the "Energy/Consumer Price" column in the "Table of rechargeable battery technologies" section in the rechargeable battery article.
United States Secretary of Energy Steven Chu predicted costs for a 40-mile range battery will drop from a price in 2008 of $12K to $3,600 in 2015 and further to $1,500 by 2020.Li-ion, Li-poly, Aluminium-air batteries and zinc-air batteries have demonstrated energy densities high enough to deliver range and recharge times comparable to conventional fossil fuelled vehicles.
Different costs are important. One issue is purchase price, the other issue is total cost of ownership. As of 2015, electric cars are more expensive to initially purchase, but cheaper to run, and in at least some cases, total cost of ownership may be lower.
According to Kammen et al., 2008, new PEVs would become cost efficient to consumers if battery prices would decrease from $1300/kWh to about $500/kWh (so that the battery may pay for itself).
In 2010, the Nissan Leaf battery pack was reportedly produced at a cost of $18,000. Nissan's initial production costs at the launch of the Leaf were therefore about $750 per kilowatt hour (for the 24 kWh battery).
In 2012, McKinsey Quarterly linked battery prices to gasoline prices on a basis of 5-year total cost of ownership for a car, estimating that $3.50/gallon equate to $250/kWh. In 2017 McKinsey estimated that electric cars are competitive at a battery pack cost of $100/kWh (around 2030), and expects pack costs to be $190/kWh by 2020.
In October 2015, car maker GM revealed at their annual Global Business Conference that they expected a price of $145 per kilowatt hour for Li-ion cells entering 2016.
Driving range parity means that the electric vehicle has the same range than an average all-combustion vehicle (500 kilometres or 310 miles), with 1+ kWh/kg batteries. Higher range means that the electric vehicles would run more kilometers without recharge.
Japanese and European Union officials are in talks to jointly develop advanced rechargeable batteries for electric cars to help nations reduce greenhouse-gas emissions. Developing a battery that can power an electric vehicle 500 kilometres (310 mi) on a single charging is feasible, said Japanese battery maker GS Yuasa Corp. Sharp Corp and GS Yuasa are among Japanese solar-power cell and battery makers that may benefit from cooperation.
Battery pack designs for Electric Vehicles (EVs) are complex and vary widely by manufacturer and specific application. However, they all incorporate a combination of several simple mechanical and electrical component systems which perform the basic required functions of the pack.
The actual battery cells can have different chemistry, physical shapes, and sizes as preferred by various pack manufacturers. Battery pack will always incorporate many discrete cells connected in series and parallel to achieve the total voltage and current requirements of the pack. Battery packs for all electric drive EVs can contain several hundred individual cells.
To assist in manufacturing and assembly, the large stack of cells is typically grouped into smaller stacks called modules. Several of these modules will be placed into a single pack. Within each module the cells are welded together to complete the electrical path for current flow. Modules can also incorporate cooling mechanisms, temperature monitors, and other devices. In most cases, modules also allow for monitoring the voltage produced by each battery cell in the stack by the Battery Management System (BMS).
The battery cell stack has a main fuse which limits the current of the pack under a short circuit condition. A "service plug" or "service disconnect" can be removed to split the battery stack into two electrically isolated halves. With the service plug removed, the exposed main terminals of the battery present no high potential electrical danger to service technicians.
The battery pack also contains relays, or contactors, which control the distribution of the battery pack's electrical power to the output terminals. In most cases there will be a minimum of two main relays which connect the battery cell stack to the main positive and negative output terminals of the pack, those supplying high current to the electrical drive motor. Some pack designs will include alternate current paths for pre-charging the drive system through a pre-charge resistor or for powering an auxiliary buss which will also have their own associated control relays. For obvious safety reasons these relays are all normally open.
The battery pack also contains a variety of temperature, voltage, and current sensors. Collection of data from the pack sensors and activation of the pack relays are accomplished by the pack 's Battery Monitoring Unit (BMU) or Battery Management System (BMS). The BMS is also responsible for communications with the world outside the battery pack.
Batteries in BEVs must be periodically recharged. BEVs most commonly charge from the power grid (at home or using a street or shop recharging point), which is in turn generated from a variety of domestic resources, such as coal, hydroelectricity, nuclear and others. Home or grid power, such as photovoltaic solar cell panels, microhydro or wind may also be used and are promoted because of concerns regarding global warming.
With suitable power supplies, good battery lifespan is usually achieved at rates not exceeding "0.5C" or so, taking two to three hours for a full charge, but faster charging can be done.
Charging time is often limited by the capacity of the grid connection. A normal household outlet delivers 1.5 kilowatts (in the US, Canada, Japan, and other countries with 110 volt supply) and 3 kilowatts (in countries with 240 V supply).
In 1995, some charging stations charged BEVs in one hour. In November 1997, Ford purchased a fast-charge system produced by AeroVironment called "PosiCharge" for testing its fleets of Ranger EVs, which charged their lead-acid batteries in between six and fifteen minutes. In February 1998, General Motors announced a version of its "Magne Charge" system which could recharge NiMH batteries in about ten minutes, providing a range of sixty to one hundred miles.
In 2005, handheld device battery designs by Toshiba were claimed to be able to accept an 80% charge in as little as 60 seconds. Scaling this specific power characteristic up to the same 7 kilowatt-hour EV pack would result in the need for a peak of 340 kilowatts of power from some source for those 60 seconds. It is not clear that such batteries will work directly in BEVs as heat build-up may make them unsafe.
In laboratories the company StoreDot from Israel reportedly first lab samples of unspecified batteries can (battery capacity in the area around 1 Ah) with as of April 2014, loaded in 30 seconds in mobile phones.
Researchers from Singapore have 2014 developed a battery that can be recharged after 2 minutes to 70 percent. The batteries rely on lithium-ion technology. However, the anode and the negative pole in the battery is no longer made of graphite, but a titanium dioxide gel. The gel accelerates the chemical reaction significantly, thus ensuring a faster charging. In particular, these batteries are to be used in electric cars. Already in 2012 researchers at the Ludwig-Maximilian-University in Munich have discovered the basic principle.
Scientists at Stanford University in California have developed a battery that can be charged within one minute. The anode is made of aluminum and the cathode made of graphite (see Aluminium-ion battery).
The charging power can be connected to the car in two ways. The first is a direct electrical connection known as conductive coupling. This might be as simple as a mains lead into a weatherproof socket through special high capacity cables with connectors to protect the user from high voltages. The modern standard for plug-in vehicle charging is the SAE 1772 conductive connector (IEC 62196 Type 1) in the US. The ACEA has chosen the VDE-AR-E 2623-2-2 (IEC 62196 Type 2) for deployment in Europe, which, without a latch, means unnecessary extra power requirements for the locking mechanism.
The second approach is known as inductive charging. A special 'paddle' is inserted into a slot on the car. The paddle is one winding of a transformer, while the other is built into the car. When the paddle is inserted it completes a magnetic circuit which provides power to the battery pack. In one inductive charging system, one winding is attached to the underside of the car, and the other stays on the floor of the garage. The advantage of the inductive approach is that there is no possibility of electrocution as there are no exposed conductors, although interlocks, special connectors and ground fault detectors can make conductive coupling nearly as safe. Inductive charging can also reduce vehicle weight, by moving more charging componentry offboard. An inductive charging proponent from Toyota contended in 1998, that overall cost differences were minimal, while a conductive charging proponent from Ford contended that conductive charging was more cost efficient.
In France, Électricité de France (EDF) and Toyota are installing recharging points for PHEVs on roads, streets and parking lots. EDF is also partnering with Elektromotive, Ltd. to install 250 new charging points over six months from October 2007 in London and elsewhere in the UK. Recharging points also can be installed for specific uses, as in taxi stands.
The range of a BEV depends on the number and type of batteries used. The weight and type of vehicle as well as terrain, weather, and the performance of the driver also have an impact, just as they do on the mileage of traditional vehicles. Electric vehicle conversion performance depends on a number of factors including the battery chemistry:
Finding the economic balance of range versus performance, battery capacity versus weight, and battery type versus cost challenges every EV manufacturer.
With an AC system or Advanced DC systems regenerative braking can extend range by up to 50% under extreme traffic conditions without complete stopping. Otherwise, the range is extended by about 10 to 15% in city driving, and only negligibly in highway driving, depending upon terrain.
BEVs (including buses and trucks) can also use genset trailers and pusher trailers in order to extend their range when desired without the additional weight during normal short range use. Discharged baset trailers can be replaced by recharged ones in a route point. If rented then maintenance costs can be deferred to the agency.
Such BEVs can become Hybrid vehicles depending on the trailer and car types of energy and powertrain.
Axillary battery capacity carried in trailers can increase the overall vehicle range, but also increases the loss of power arising from aerodynamic drag, increases weight transfer effects and reduces traction capacity.
An alternative to recharging is to exchange drained or nearly drained batteries (or battery range extender modules) with fully charged batteries. This is called battery swapping and is done in exchange stations.
On the other hand, MIRA has announced a retrofit hybrid conversion kit that provides removable battery packs that plug into a wall outlet for charging. Also XP Vehicles uses extension-cord-free charging hot-swap battery (removable power pack to recharge at home without extension cord).
Features of swap stations include:
Concerns about swap stations include:
Zinc-bromine flow batteries can be re-filled using a liquid, instead of recharged by connectors, saving time.
Three companies are working on battery lease plans. Greenstop has completed trials of their ENVI Grid Network which allows consumers to easily monitor and recharge electric vehicle batteries. Think Car USA plans to lease the batteries for its City electric car to go on sale next year. Better Place is creating a system for consumers to "subscribe" to a service that offers recharging stations and battery exchange.
Smart grid allows BEVs to provide power to the grid at any time, especially:
Pacific Gas and Electric Company (PG&E) has suggested that utilities could purchase used batteries for backup and load levelling purposes. They state that while these used batteries may be no longer usable in vehicles, their residual capacity still has significant value.
Individual batteries are usually arranged into large battery packs of various voltage and ampere-hour capacity products to give the required energy capacity. Battery service life should be considered when calculating the extended cost of ownership, as all batteries eventually wear out and must be replaced. The rate at which they expire depends on a number of factors.
The depth of discharge (DOD) is the recommended proportion of the total available energy storage for which that battery will achieve its rated cycles. Deep cycle lead-acid batteries generally should not be discharged to below 20% of total capacity. More modern formulations can survive deeper cycles.
In real world use, some fleet Toyota RAV4 EVs, using Nickel-metal hydride battery, have exceeded 100,000 miles (160,000 km) with little degradation in their daily range. Quoting that report's concluding assessment:
Lithium ion batteries are perishable to some degree; they lose some of their maximum storage capacity per year even if they are not used. Nickel metal hydride batteries lose much less capacity and are cheaper for the storage capacity they give, but have a lower total capacity initially for the same weight.
Jay Leno's 1909 Baker Electric (see Baker Motor Vehicle) still operates on its original Edison cells. Battery replacement costs of BEVs may be partially or fully offset by the lack of regular maintenance such as oil and filter changes required for ICEVs, and by the greater reliability of BEVs due to their fewer moving parts. They also do away with many other parts that normally require servicing and maintenance in a regular car, such as on the gearbox, cooling system, and engine tuning. And by the time batteries do finally need definitive replacement, they can be replaced with later generation ones which may offer better performance characteristics.
Lithium iron phosphate batteries reach according to the manufacturer more than 5000 cycles at respective depth of discharge of 70%. As the world's largest manufacturer of lithium iron phosphate batteries are concerned BYD, which has developed through precision manufacturing a wide range of cells for deep cycle applications, such as in use in stationary storage systems. After 7500 cycles with discharge of 85% this still have a spare capacity of at least 80% at a rate of 1 C; which corresponds with a full cycle per day to a lifetime of min. 20.5 years. The lithium iron phosphate battery Sony Fortelion has after 10,000 cycles at 100% discharge level still a residual capacity of 71%. This accumulator is since 2009 on the market.
Plug-in America has among drivers of the Tesla Roadster (2008), a survey carried out with respect to the service life of the installed battery. It was found that after 100,000 miles = 160,000 km, the battery still had a remaining capacity of 80 to 85 percent. This was regardless of in which climate zone the car is moved. The Tesla Roadster was built and sold between 2008 and 2012. For its 85-kWh batteries in the Tesla Model S Tesla are 8-year warranty with unlimited mileage.
As of December 2016Nissan Leaf, with more than 250,000 units sold since its inception in 2010. Nissan stated in 2015 that until then only 0.01 percent of batteries had to be replaced because of failures or problems and then only because of externally inflicted damage. There are a few vehicles that have already covered more than 200,000 km; none of these had any problems with the battery., the world's all-time best-selling electric car is the
At the end of their useful life, batteries can be recycled.
Firefighters and rescue personnel receive special training to deal with the higher voltages and chemicals encountered in electric and hybrid electric vehicle accidents. While BEV accidents may present unusual problems, such as fires and fumes resulting from rapid battery discharge, many experts agree that BEV batteries are safe in commercially available vehicles and in rear-end collisions, are safer than gasoline-propelled cars with a rear gasoline tanks.
Usually, battery performance testing includes the determination of:
Performance testing simulates the drive cycles for the drive trains of Battery Electric Vehicles (BEV), Hybrid Electric Vehicles (HEV) and Plug in Hybrid Electric Vehicles (PHEV) as per the required specifications of car manufacturers (OEMs). During these drive cycles, controlled cooling of the battery can be performed, simulating the thermal conditions in the car.
In addition, climatic chambers assure constant environmental conditions during the characterization and allow the simulation to be performed for the full automotive temperature range covering climatic conditions.
Patents may be used to suppress development or deployment of this technology. For instance, patents relevant to the use of Nickel metal hydride cells in cars were held by an offshoot of Chevron Corporation, a petroleum company, who maintained veto power over any sale or licensing of NiMH technology.
Battery-operated vehicles (like the Nissan Leaf) are projected to have annual sales in 2020 of 100,000 units in the U.S. and 1.3 million worldwide -- 1.8 percent of the 71 million cars expected to be sold in 2020. Another 3.9 million plug-ins and hybrids will be sold worldwide, bringing the total electric and hybrid market to about 7 percent of all cars sold in 2020.
Bolloré a French automotive parts group developed a concept car the "Bluecar" using Lithium metal polymer batteries developed by a subsidiary Batscap. It had a range of 250 km and top speed of 125 km/h.
Electric double-layer capacitors (or "ultracapacitors") are used in some electric vehicles, such as AFS Trinity's concept prototype, to store rapidly available energy with their high power density, in order to keep batteries within safe resistive heating limits and extend battery life.
Since commercially available ultracapacitors have a low energy density no production electric cars use ultracapacitors exclusively. But using an Electric car with both Battery and ultracapacitor can reduce the limitations of both.
As U.S. President Barack Obama announced 48 new advanced battery and electric drive projects that would receive $2.4 billion in funding under the American Recovery and Reinvestment Act. These projects will accelerate the development of U.S. manufacturing capacity for batteries and electric drive components as well as the deployment of electric drive vehicles, helping to establish American leadership in creating the next generation of advanced vehicles.
The announcement marks the single largest investment in advanced battery technology for hybrid and electric-drive vehicles ever made. Industry officials expect that this $2.4 billion investment, coupled with another $2.4 billion in cost share from the award winners, will result directly in the creation tens of thousands of manufacturing jobs in the U.S. battery and auto industries.
The new awards cover $1.5 billion in grants to United States-based manufacturers to produce batteries and their components and to expand battery recycling capacity.
U.S. Vice President Joe Biden announced in Detroit over $1 billion in grants to companies and universities based in Michigan. Reflecting the state's leadership in clean energy manufacturing, Michigan companies and institutions are receiving the largest share of grant funding of any state. Two companies, A123 Systems and Johnson Controls, will receive a total of approximately $550 million to establish a manufacturing base in the state for advanced batteries, and two others, Compact Power and Dow Kokam, will receive a total of over $300 million for manufacturing battery cells and materials. Large automakers based in Michigan, including GM, Chrysler, and Ford, will receive a total of more than $400 million to manufacture batteries and electric drive components. And three educational institutions in Michigan -- the University of Michigan, Wayne State University in Detroit, and Michigan Technological University in Houghton, in the Upper Peninsula -- will receive a total of more than $10 million for education and workforce training programs to train researchers, technicians, and service providers, and to conduct consumer research to accelerate the transition towards advanced vehicles and batteries.
Energy Secretary Steven Chu visited Celgard, in Charlotte, North Carolina, to announce a $49 million grant for the company to expand its separator production capacity to serve the expected increased demand for lithium-ion batteries from manufacturing facilities in the United States. Celgard will be expanding its manufacturing capacity in Charlotte, North Carolina, and nearby Concord, North Carolina, and the company expects the new separator production to come online in 2010. Celgard expects that approximately hundreds of jobs could be created, with the first of those jobs beginning as early as fall 2009.
EPA Administrator Lisa Jackson was in St. Petersburg, Florida, to announce a $95.5 million grant for Saft America, Inc. to construct a new plant in Jacksonville on the site of the former Cecil Field military base, to manufacture lithium-ion cells, modules and battery packs for military, industrial, and agricultural vehicles.
Deputy Secretary of the Department of Transportation John Porcari visited East Penn Manufacturing Co, in Lyon Station, Pennsylvania, to award the company a $32.5 million grant to increase production capacity for their valve regulated lead-acid batteries and the UltraBattery, a lead-acid battery combined with a carbon supercapacitor, for micro and mild hybrid applications.
The 2012 per-mile cost under this scenario will be 10¢ per mile. If the batteries are able to achieve 3,000 100-mile charge cycles and the vehicle is driven 15,000 miles per year, the 2012 per-mile cost is approximately 6.7¢ per mile. The likely lifetime of electric vehicle batteries is likely to fall somewhere within this range.
The cost of electricity for electric cars is on the order of 2¢ per mile, though electricity prices vary by region across the U.S.
Tesla's current batteries cost $200-$300 per kilowatt hour.
Eine neue Art von Akku erreicht schon nach zwei Minuten am Strom eine 70-prozentige Ladung. Vor allem Elektroautos sollen profitieren.
,,Die Tests setzten die Batterien extremen Belastungen aus. So wurden über einen Zeitraum von 5 Jahren bei einer Entladungstiefe von 60 % mehr als 10.000 äquivalente Vollzyklen erreicht." and ,,Simulationen, die sich auf unsere Laborergebnisse und die unserer Kollegen vom ZSW stützen, zeigen, dass bei Berücksichtigung beider Alterungsprozesse die Batterien im BPT-S 5 Hybrid bis zu 20 Jahre betriebsfähig sind"
,,Die Zellen haben laut Hersteller eine voraussichtliche Lebensdauer von 20 Jahren und könnten bis zu 15.000 Mal aufgeladen werden"