Waterproofing is the process of making an object or structure waterproof or water-resistant so that it remains relatively unaffected by water or resisting the ingress of water under specified conditions. Such items may be used in wet environments or underwater to specified depths.
Water resistant and waterproof often refer to penetration of water in its liquid state and possibly under pressure, whereas damp proof refers to resistance to humidity or dampness. Permeation of water vapor through a material or structure is reported as a moisture vapor transmission rate.
Waterproofing is used in reference to building structures (such as basements, decks, or wet areas), watercraft, canvas, clothing (raincoats or waders), electronic devices and paper packaging (such as cartons for liquids).
In construction, a building or structure is waterproofed with the use of membranes and coatings to protect contents, and structural integrity. The waterproofing of the building envelope in construction specifications is listed under 07 - Thermal and Moisture Protection within MasterFormat 2004, by the Construction Specifications Institute, and includes roofing and waterproofing materials.
In building construction, waterproofing is a fundamental aspect of creating a building envelope, which is a controlled environment. The roof covering materials, siding, foundations, and all of the various penetrations through these surfaces must be water-resistant and sometimes waterproof. Roofing materials are generally designed to be water-resistant and shed water from a sloping roof, but in some conditions, such as ice damming and on flat roofs, the roofing must be waterproof. Many types of waterproof membrane systems are available, including felt paper or tar paper with asphalt or tar to make a built-up roof, other bituminous waterproofing, ethylene propylene diene monomer EPDM rubber, hypalon, polyvinyl chloride, liquid roofing, and more.
Walls are not subjected to standing water, and the water-resistant membranes used as housewraps are designed to be porous enough to let moisture escape. Walls also have vapor barriers or air barriers. Damp proofing is another aspect of waterproofing. Masonry walls are built with a damp-proof course to prevent rising damp, and the concrete in foundations needs to be damp-proofed or waterproofed with a liquid coating, basement waterproofing membrane (even under the concrete slab floor where polyethylene sheeting is commonly used), or an additive to the concrete.
Within the waterproofing industry, below-ground waterproofing is generally divided into two areas:
Tanking: This is waterproofing used where the below-ground structure will be sitting in the water table continuously or periodically. This causes hydrostatic pressure on both the membrane and structure, and requires full encapsulation of the basement structure in a tanking membrane, under slab and walls.
Damp proofing: This is waterproofing used where the water table is lower than the structure and there is good free-draining fill. The membrane deals with shedding of water and the ingress of water vapor only, with no hydrostatic pressure. Generally, this incorporates a damp proof membrane (DPM) to the walls with a polythene DPM under slab. With higher grade DPM, some protection from short-term Hydrostatic pressure can be gained by transitioning the higher quality wall DPM to the slab polythene under footing, rather than at the footing face.
In buildings using earth sheltering, a potential problem is too much humidity, so waterproofing is critical. Water seepage can lead to mold growth, causing significant damage and air quality issues. Properly waterproofing foundation walls is required to prevent deterioration and seepage.
Another specialized area of waterproofing is roof top decks and balconies. Waterproofing systems have become quite sophisticated and are a very specialized area. Failed waterproof decks, polymer or tile, are one of the leading causes of water damage to building structures, and of personal injury when they fail. Where major problems occur in the construction industry is when improper products are used for the wrong application. While the term waterproof is used for many products, each of them has a very specific area of application, and when manufacturer specifications and installation procedures are not followed, the consequences can be severe. Another factor, is the impact of expansion and contraction on waterproofing systems for decks. Decks constantly move with changes in temperatures, putting stress on the waterproofing systems. One of the leading causes of waterproof deck system failures is the movement of underlying substrates (plywood) that cause too much stress on the membranes resulting in a failure of the system. While beyond the scope of this reference document, waterproofing of decks and balconies is a complex of many complimentary elements. These include the waterproofing membrane used, adequate slope-drainage, proper flashing details, and proper construction materials.
The penetrations through a building envelope must be built in a way such that water does not enter the building, such as using flashing and special fittings for pipes, vents, wires, etc. Some caulkings are durable, but many are unreliable for waterproofing.
Also, many types of geomembranes are available to control water, gases, or pollution.
From the late 1990s to the 2010s, the construction industry has had technological advances in waterproofing materials, including integral waterproofing systems and more advanced membrane materials. Integral systems such as hycrete work within the matrix of a concrete structure, giving the concrete itself a waterproof quality. There are two main types of integral waterproofing systems: the hydrophilic and the hydrophobic systems. A hydrophilic system typically uses a crystallisation technology that replaces the water in the concrete with insoluble crystals. Various brands available in the market claim similar properties, but not all can react with a wide range of cement hydration by-products and thus require caution. Hydrophobic systems use fatty acids to block pores within the concrete, preventing water passage.
Sometimes the same materials used to keep water out of buildings are used to keep water in, such as pool or pond liners.
New membrane materials seek to overcome shortcomings in older methods like polyvinyl chloride (PVC) and high-density polyethylene (HDPE). Generally, new technology in waterproof membranes relies on polymer-based materials that are very adhesive to create a seamless barrier around the outside of a structure.
The standards for waterproofing bathrooms in domestic construction have improved over the years, due in large part to the general tightening of building codes.
Some garments, and tents, are designed to give greater or lesser protection against rain. For urban use raincoats and jackets are used; for outdoor activities in rough weather there is a range of hiking apparel. Typical descriptions are "showerproof", "water resistant", and "waterproof". These terms are not precisely defined. A showerproof garment will usually be treated with a water-resisting coating, but is not rated to resist a specific hydrostatic head. This is suitable for protection against light rain, but after a short time water will penetrate. A water-resistant garment is similar, perhaps slightly more resistant to water but also not rated to resist a specific hydrostatic head. A garment described as waterproof will have a water-repellent coating, with the seams also taped to prevent water ingress there. Better waterproof garments have a membrane lining designed to keep water out but allow trapped moisture to escape ("breathability")--a totally waterproof garment would retain body sweat and become clammy. Waterproof garments specify their hydrostatic rating, ranging from 1,500 for light rain, to 20,000 for heavy rain.
Waterproof garments are intended for use in weather conditions which are often windy as well as wet, and are usually also wind resistant.
Waterproofing methods have been implemented in many types of objects, including paper packaging, cosmetics, and more recently, consumer electronics. Even though it is possible to find waterproof wrapping or other types of protective cases for electronic devices, a new technology enabled the release of diverse waterproof smartphones and tablets in 2013. This method is based on a special nanotechnology coating a thousand times thinner than a human hair which protects electronic equipment from damage due to the penetration of water. Several manufacturers use the nano coating method on their smartphones, tablets, and digital cameras.